Last Updated on August 14, 2023 by admin

Netgear WiFi extender red light has been one of the most annoying issues for decades. If you are also experiencing the same issue, then you will be glad to know that – we have got you covered. In this article, we will provide you some of the best yet effective tips that will help you get rid of Netgear extender red light issue from the comfort of your home. So, without much delay, let’s get started!
Fixed: Netgear Extender Red Light Issue
Fix 1: Contact Your ISP
A weak or poor internet connection can also force you experience red light issue on your Netgear WiFi range extender. Therefore, to get the issue fixed, contact your ISP. Confirm from your service provider, if there isn’t any issue from his end. If everything is fine from your internet service provider’s end, the chances are that the connection between your Netgear extender and router is not stable.
Fix 2: Verify the Connection
If have used an Ethernet cable to connect your Netgear WiFi range extender and router, ensure that it is non-damaged. On the off chance if the cable you are using consists of any sort of cuts and damages, then we suggest you replace it right away.
Once you’re done connecting your Netgear device and router using an Ethernet source, try to access the settings page of your extender using 192.168.1.250 IP.
Fix 3: Keep WiFi Interference at Bay
Another effective thing that you can try to troubleshoot the Netgear extender red light issue is to keep the interference-creating WiFi obstructions at bay. Thus, to get the most out of your Netgear WiFi range extender, keep it away from cordless phones, treadmills, reflective surfaces, baby monitors, smart HD television, gaming consoles, Bluetooth speakers, etc.
Additionally, we suggest you – not to place your Netgear WiFi range extender near to corners, concrete walls, in reach of public WiFi, non-ventilated and congested surface.
Besides, we suggest you to place your Netgear WiFi range extender:
At the middle location in your home
Near to your WiFi router
On a higher and open shelf
Away from corners, windows, cupboards or cabinets
Fix 4: Perform Firmware Update
Performing Netgear extender firmware update is one of the ultimate ways to fix major technical glitches with the device. If you haven’t updated the firmware of the device after completing the Netgear range extender setup process, you will surely face the red light issue. Thus, to fix technical issues with your Netgear WiFi range extender, consider updating its firmware to the most latest version. To get the job done, navigate to the Netgear’s official site and follow the on-screen instructions. The firmware of the Netgear extender can also be updated by navigating to the settings page of the device using 192.168.1.250 IP or mywifiext.net web address.
Fix 5: Restart Your Netgear Extender
Most of the time, minor technical issues with the device can also force your device to flash red light on it. However, to get the issue fixed, restart or power cycle your Netgear WiFi range extender. To restart the device, follow the guidelines listed below in exact given order:
First of all, you have to disconnect all the devices that are currently connected to your router.
Once you’re done, unplug your Netgear extender from its wall outlet.
Wait for a couple of seconds.
Plug your Netgear WiFi extender back in.
Don’t forget to press the power (on/off) button.
Connect your Netgear range extender to the router using an Ethernet or a wireless source.
Now, check whether you are experiencing red light issue or not. Apart from this, make sure that you have configured your range extender properly. Bear in mind – a partial or incomplete Netgear WiFi extender setup process may also let you experience the red light issue on your device.
The Last Words
Anticipating that – after following the troubleshooting steps mentioned in this article – have helped you out to get rid of red light issue on your Netgear WiFi range extender? However, if you are still unable to cope up with the issue, let us know via comments.
Read More: A Guide to Backup and Restore Settings on Netgear Extender